The device, service, Nissan Maxima QX repair - Removal and installation of the main cylinder of coupling//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
- Coupling and power shafts
   General information
   Coupling - the general information and check of a condition of components
   Removal and installation of the main cylinder of coupling
   Removal and installation of the executive cylinder of coupling
   Air removal from a hydraulic path of a drive of switching off of coupling
   Removal, check of a condition and installation of components of assembly of coupling
   Removal, check of a condition and installation of the vyzhimny bearing and lever of switching off of coupling
   Adjustment of a pedal of coupling
   Check of serviceability of functioning and replacement of the sensor switch of disconnection of a chain of a starter
   Power shafts - the general information and condition check
   Removal and installation of power shafts
   Check of a condition and replacement of assembly of the basic bearing
   Replacement of protective covers and check of a condition of CV JOINTS
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Removal and installation of the main cylinder of coupling

Components of assembly of the main cylinder of coupling

1 — the Case
2 — the Tank of hydraulic liquid
3 — a tank Cover
4 — the Returnable spring
5 — Sealing cuffs
6 — the Piston

7 — a valve Emphasis (acts in film at spring and piston dismantle, 1.5 ÷ 2.9 Nanometers)
8 — the Pusher
9 — the Emphasis
10 — the Lock ring
11 — the Boot
12 — the Lock-nut (8 ÷ 11 Nanometer)

REMOVAL

 PERFORMANCE ORDER

1. The design of the main hydraulic cylinder of coupling is presented on an illustration.
2. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. Under the dashboard take a fixing pin and disconnect from the lever of a pedal of coupling a cutting finger of a pusher of the main hydraulic cylinder.

4. Remove the pump of the device of automatic control of speed (ASCD). Disconnect from assembly of the main cylinder of coupling the hydraulic line, - in order to avoid a rounding off шлицов nuts, weakening of shtutserny knot is reasonable for making by means of a special cap natural a cutting head. Prepare rags for collecting spilled hydraulic liquid.

 In order to avoid damage of a paint and varnish covering do not allow hit of brake liquid on the painted body surfaces.

5. Give nuts of fastening of the main cylinder on a back partition of an impellent compartment. Remove Assembly of the main cylinder (try not to spill brake liquid).

INSTALLATION

 PERFORMANCE ORDER

1. Get assembly of the main cylinder on the regular place and fix it nuts, having by hand tightened the last.
2. Connect to the main cylinder the hydraulic line, - try not to warp a cap nut of the shtutserny socket in order to avoid irreversible damage of the last owing to carving failure.
3. Strongly tighten fixing nuts and the union of the hydraulic line.
4. Connect a cylinder pusher to a pedal of coupling and fix a new pin a cutting finger.
5. Fill in in the tank necessary amount of brake DOT 3 liquid (see. Head of Control and routine maintenance), then give from a path air jams (see. The section air Removal from a hydraulic path of a drive of switching off of coupling).
6. Check correctness of installations of height and a free wheeling of a pedal of coupling, in case of need make the corresponding adjustment (see. Section Adjustment of a pedal of coupling).