Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Replacement of the dosing-out valve regulator
   Check of a condition and replacement of brake lines and hoses
   Pumping of brake system
   Check of serviceability of functioning/tightness, replacement and adjustment of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Cable replacement (ов) drive of the parking brake
   Adjustment of a pedal of a foot brake
   Check of serviceability of functioning and replacement of the sensor switch of stoplights
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Cable replacement (ов) drive of the parking brake

The scheme of laying of a hummock drive of the parking brake is presented on an illustration.

Scheme of laying of a torsovy drive of the parking brake

1 — the Control lever
2 — the Bolt (8 ÷ 11 Nanometer)
3 — the Adjusting nut (3.1 ÷ 4.3 Nanometer)
4 — the Nut of fastening of a basic arm of an intermediate clamp (8 ÷ 11 Nanometer)
5 — the Right back section of a hummock drive

6 — the Bolt of fastening of an arm of an intermediate clamp (8 ÷ 11 Nanometer)
7 — the Left back section of a hummock drive
8 — the Bolt (6 ÷ 11 Nanometer)
9 — the Brake mechanism of disk type
10 — the Brake mechanism of drum-type type

Back sections of a hummock drive

 PERFORMANCE ORDER

1. Make sure of completeness of an otpuskaniye of the parking brake.
2. Prop up protivootkatny boots forward wheels, weaken nuts of fastening of back wheels, then поддомкратьте a back of the car and establish it on props.
3. On the models equipped with drum-type brake mechanisms of back wheels, remove brake boots and disconnect a driving cable from the executive lever of the parking brake (see. Section Replacement of boots of drum-type brake mechanisms of back wheels). Remove from the cable end a spring, then отболтите the holder of a cover of a cable from a brake board. Liberate hummock assembly from a board of the brake mechanism.

4. On models with disk back brake mechanisms remove a lock plate of fastening of a cable to a pribolchenny arm to a support. Liberate a cable from the bifurcate termination of the executive lever.

5. To Otboltita all arms of intermediate clamps of fastening of a cable on frame and suspension bracket elements.

6. Remove the thermofilter of the catalytic converter.

7. Give located at once behind assembly of the equalizer of a nut of fastening of covers of cables, liberate tips of cables from the equalizer.

8. Installation is made upside-down.
9. Make adjustment of a hummock drive of the parking brake (see. Section Adjustment of the parking brake).

Forward section of a hummock drive

 PERFORMANCE ORDER

1. Remove the central console (see. Head Body).

2. Disconnect electroconducting of the sensor switch of a control lamp of raising of the parking brake.

The contact socket of electroconducting of the sensor switch of a control lamp of raising of the parking brake (And), nuts of fastening of a control lever (In) and bolts of fastening of a directing plate (C)

3. Give an adjusting nut of a hummock drive.
4. Turn out two bolts from the control lever basis the parking brake.
5. To Poddomkratta a car back also establish it on props. Prop up forward wheels protivootkatny boots and remove the thermofilter of the catalytic converter.
6. Give two nuts at once behind assembly of the equalizer and liberate from the last tips of back sections of a hummock drive.
7. In salon of the car turn out two bolts of fastening of a directing plate of a cable and involve in salon assembly of a forward cable with the equalizer.
8. Installation is made upside-down.
9. Make adjustment of a drive of the parking brake (see. Section Adjustment of the parking brake).