Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment



Removal and installation of components of a back suspension bracket of models from 1995 вып.

 PERFORMANCE ORDER

1. Weaken wheel nuts. To Poddomkratta a car back also establish it on props. Remove back wheels.
2. On the models equipped with ABS, remove sensors of turns of back wheels. Turn out coupling bolts and liberate plaits of electroconducting of sensors from basic arms.
3. Disconnect driving cables of the parking brake and remove supports and disks of brake mechanisms (see. Head Brake system). Tie up supports to prutka of screw springs.
4. If the back bridge is subject to replacement, remove assemblies of naves with wheel bearings (see. The section Removal and installation of assembly of a back nave with the wheel bearing).
5. To Poddomkratta the back bridge one jack under the middle, or two under the ends.
6. To Otboltita from the bridge the bottom ends of shock-absorbers (see. Section Removal, check of a condition and installation of racks of a back suspension bracket).

7. Disconnect a cross-section jet bar from the car chassis.

8. Give nuts and take axial bolts of fastening of longitudinal levers of a suspension bracket. By means of the assistant accurately take assembly of the back bridge with a jet bar from under the car.

9. Estimate a condition of plugs of a jet bar, a rod of management and longitudinal levers. Defective components replace.
10. A cross-section jet bar with a rod of management can be removed from assembly of the back bridge by a way of an otpuskaniye of the corresponding fixture. At installation of components into place track, that the bar appeared is developed by marking in the form of an arrow up, the plug of a rod of management was turned by the party with an opening of smaller diameter to a bar.

INSTALLATION

 PERFORMANCE ORDER

1. Installation of components is made as it should be the return to an order of their dismantle. Track, that all fixture was tightened with demanded effort.

 The final tightening of fixture of shock-absorbers and jet bar should be made after elements of a suspension bracket will be deduced on normal working height, - use a jack. The tightening of nuts of axial bolts of longitudinal levers should be made at the unloaded suspension bracket (in we string the provision of components).

2. Efforts of a tightening of carving fixture of components of brake mechanisms are given in Specifications to Head Brake system.
3. Establish to the place of a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see. Head of Control and routine maintenance).