Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
9a1e70e9



Removal and installation of a steering wheel

The models equipped with safety cushions

 Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Chapter 12). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation. In order to avoid SRS system damage, Track, that the steering shaft was not turned after removal of a steering wheel. Block a column the ignition key at the rectilinear provision of forward wheels.

REMOVAL

 PERFORMANCE ORDER

1. Disconnect from the battery at first a negative wire, then positive.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! Before starting removal of a steering wheel обожите not less than 10 minutes.

2. Bring forward wheels of the car into rectilinear situation.

3. Remove a small cover of an opening of access in a lateral part of a casing of a steering column and disconnect electroconducting from the safety cushion module.

4. Having hooked a small screw-driver, remove decorative covers of screws of fastening of the module of a safety cushion. Screws have heads of the TORX type and are covered with special fixing structure, and therefore, at module installation into place are subject to replacement without fail. Take the safety cushion module from a stupichny part of a steering wheel.

 Try not to turn the safety cushion module the face to itself as its casual operation is fraught with receiving heavy traumas (see. Head Onboard electric equipment).

5. Give a nut of fastening of a steering wheel, then mark the provision of a nave of the last rather steering shaft, - such marking can already take place.

6. Disconnect electroconducting темпостата.

7. By means of a special stripper remove a steering wheel from a shaft of a steering column.

 At all do not force down a wheel from a shaft a hammer, after removal of a wheel do not rotate a steering shaft!

8. In need of check of a condition or replacement of podrulevy switches remove spring contact assembly.

 Regardless because, spring contact will act in film or not, an adhesive tape attach the central part of its nave to an external ring so that completely to exclude possibility of its provorachivaniye. Do not allow a provorachivaniye of a steering shaft at the removed steering wheel!

9. In case of need turn out fixing screws, release a clamp, disconnect electroconducting and remove assembly of spring contact from a steering column.

INSTALLATION

 PERFORMANCE ORDER

1. Make sure that forward wheels of the car are established in rectilinear situation. Turn established from above on a shaft of a steering column spring contact of the module of a safety cushion clockwise before emergence of feeling of appreciable resistance, then return it on 2.5 turns in the opposite direction and achieve combination of two index labels.

2. Pass electroconducting of the module of a safety cushion and a control system of speed through a steering wheel and establish the last on the regular place. Track, that pins of spring contact correctly entered into gearing with reciprocal openings in a back part of a stupichny part of a steering wheel. Make sure of correctness of combination of landing labels.
3. Screw a fixing nut and tighten it with demanded effort.
4. Establish the module of a safety cushion and fix it new bolts with TORX type heads. Establish the switch темпостата and lateral covers of a casing of a steering column.
5. Connect electroconducting to the safety cushion module. Establish the bottom cover.
6. Make sure of serviceability of functioning of the module of a safety cushion, - at ignition inclusion on the dashboard approximately for 7 seconds the corresponding control lamp should light up.

Models without safety cushions

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. For removal of the button of a horn hook it from below the suitable tool and liberate from assembly of a steering wheel.
3. Further act in an order stated in paragraphs with 5 on 7.

INSTALLATION

 PERFORMANCE ORDER

1. Before installation of a steering wheel grease a sliding ring of klaksonny contact and a sliding part of a pin of the returnable switch of indexes of turns with universal greasing.
2. Track, that the nut of fastening of a steering wheel was tightened with demanded effort.
3. Connect electroconducting and establish on assembly the horn button.
4. Connect a negative wire to the battery.