Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment



Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket

REMOVAL

 PERFORMANCE ORDER

1. Weaken wheel nuts. To Poddomkratta a car front also establish it on props. Remove forward wheels.

2. Liberate a flexible brake hose from an arm on a suspension bracket rack.

3. Give two nuts and by means of a hammer and a drift beat out two bolts of fastening of a rack to a rotary fist.

4. Separate a rack from assembly of a rotary fist, - try not to allow an excessive pulling of the internal CV JOINT of a power shaft, in order to avoid damage of a brake hose do not allow excessive loss of a fist outside.

5. Holding a rack, give three top nuts of its fastening on a basic ledge of a mudguard of a wheel arch.

 Giving the last nut, hold a rack with a free hand. Take rack-mount assembly through a wheel arch.

CHECK

 PERFORMANCE ORDER

1. Attentively examine the rack case outside, checking it on existence of signs of leakages of hydraulic liquid, cracks, dents and the other mechanical defects demanding performance of the corresponding regenerative repair, or assembly replacement.
2. Check rounds of a rack-mount spring on existence of chips, cracks and the other damages of a sheeting fraught with development of corrosion a prutka. Estimate a condition of a rubber pillow of a saddle of a spring.
3. In case of need make rack dismantling (see. Section shock-absorber Replacement / screw spring of rack-mount assembly).

INSTALLATION

 PERFORMANCE ORDER

1. Get rack-mount assembly through a wheel arch on the regular place. Accurately pass fixing hairpins in openings of the top support. At once screw on nut hairpins, having tightened them while only by hand.

 In view of considerable weight of amortizatorny assembly it will be reasonable to secure with the help of the assistant.

2. Fill a rotary fist in a rack-mount flange and pass in the nests two fixing bolts. Screw new nuts and tighten them with demanded effort.
3. Fix a brake hose in an arm on a rack, latch a clamp.
4. Establish wheels, lower the car on the earth and tighten nuts of fastening of wheels with demanded effort (see. Head of Control and routine maintenance).
5. Tighten with demanded effort the top nuts of fastening of rack-mount assembly.