The device, service, Nissan Maxima QX repair - shock-absorber Replacement / a screw spring of rack-mount assembly//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
9a1e70e9



Shock-absorber replacement / screw spring of rack-mount assembly

Check the rack-mount assembly removed from the car on existence of signs of leaks, dents, cracks and other mechanical damages. Examine a screw spring on existence of chips, cracks, prosedaniye signs, and rubber pillows of its saddles on existence of signs of hardening and material aging. At firm car repair shops of the Nissan company always it is possible to get on an exchange basis shock-absorbers assembled with screw springs that allows to reduce temporary and monetary expenses essentially. In view of told before starting assembly dismantle for the purpose of performance of its regenerative repair, carry out marketing, having been defined in the prices for replaceable components and having compared them to costs of acquisition of the restored rack.

 Removal of a screw spring from amortizatorny assembly is connected with potential danger and should be made only with use of the high-quality special tool.

DISMANTLING

 PERFORMANCE ORDER

1. Remove rack-mount assembly from the car (see. Section shock-absorber Replacement / screw spring of rack-mount assembly or Removal, check of a condition and installation of racks of a back suspension bracket). Clamp shock-absorber assembly in a vice with soft sponges (not too strongly).

2. Following instructions of manufacturers, establish the tool for a szhimaniye of a screw spring. Tightening nuts on tool hairpins, compress a spring so completely to unload the basis of the top support.

3. Give a nut of a rod of the shock-absorber.

4. Remove the top support of a rack from a piston rod of the shock-absorber. Check freedom of rotation of the bearing, in case of need replace a support. Estimate a condition of rubber details, in case of identification of signs of destruction of a material replace defective units.

5. Remove from a shock-absorber rod the top saddle of a spring, estimate a condition of its rubber pillow, in case of need make replacement. Remove from a rod a rubber pillow of the top saddle.

6. Accurately remove from the shock-absorber the compressed screw spring and transfer it to a safe place.

 Try not to turn the compressed spring end faces to itself!

7. Remove from a shock-absorber rod a rubber protective cover.
8. Estimate a condition of the bottom rubber pillow, in case of need make its replacement.

ASSEMBLY

 PERFORMANCE ORDER

1. At replacement of a rubber pillow of the bottom saddle of a spring track, that it was planted by the party equipped with notches to a saddle. Extend a shock-absorber rod for all length of the course and put on it a rubber protective cover.

2. Accurately plant the compressed screw spring in the bottom saddle. Track, that the end face a prutka of a spring got to most lowered part of a pillow.

3. Establish on assembly the top rubber pillow and the top saddle of a spring. Track, that the saddle appeared is developed by cut outside from the diametrical plane of the car.

4. Plant on a shock-absorber rod a boot and the top support of a rack.
5. Screw a nut and tighten it with demanded effort. Remove the adaptation for a szhimaniye of a screw spring.
6. Establish a collected rack on the regular place (see. Section shock-absorber Replacement / screw spring of rack-mount assembly or Removal, check of a condition and installation of racks of a back suspension bracket).