Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment



Removal and installation of assembly of a rotary fist with a nave

 Remember that developed in the course of operation of brake mechanisms the dust can contain extremely unhealthy the person asbestos. At all do not blow off a dust the compressed air and do not inhale it, - at service of mechanisms put on a protective mask or a respirator. At all do not use for rubbing of components of brake system gasoline or solvents on an oil basis, - apply only firm cleaners or methyl alcohol!

REMOVAL

 PERFORMANCE ORDER

1. Remove a decorative cap of a disk or a cover of a stupichny nut. Take шплинт and wring out a tag of a lock washer, then weaken a stupichny nut (see. Head Coupling and power shafts).

 If the face head does not pass in an opening in the wheel center, temporarily establish to the place of the last запаску.

2. Weaken nuts of fastening of a wheel, поддомкратьте a front of the car and establish it on props. Remove a wheel.
3. Remove a support of the brake mechanism and a brake disk (see. Head Brake system). Liberate a brake hose from an arm on rack-mount assembly. On the equipped ABS models disconnect electroconducting and remove the wheel sensor.
4. Give nuts of fastening of a rack of a suspension bracket to a rotary fist, however, do not beat out while fixing bolts.
5. Liberate from the lever of a rotary fist a tip of steering draft (see. Section Removal and installation of tips of steering drafts).
6. Liberate a spherical support from assembly of a rotary fist (see. Section Removal and installation of a control lever of a forward suspension bracket).
7. Beat out fixing bolts and separate a rotary fist from rack-mount assembly, at the same time pushing out a pin of a power shaft from a wheel nave (if the shaft "became attached", use a hammer and a brass drift). Tie up the liberated power shaft a wire to suspension bracket elements.

INSTALLATION

 PERFORMANCE ORDER

1. Grease shlitsa of a pin of a power shaft with universal greasing. Get assembly of a rotary fist on the regular place, pass in a nave a pin of a power shaft.
2. Fill a fist in a rack flange, pass bolts, then screw, but do not tighten, fixing nuts.
3. Connect a suspension bracket control lever to a rotary fist (see. Section Removal and installation of a control lever of a forward suspension bracket).
4. Fill in the fist lever a tip of steering draft (see. Section Removal and installation of tips of steering drafts). Tighten with demanded effort of a nut of bolts of fastening of a rack, and also support fixture to the lever and a nut of a tip of draft.
5. Establish on a nave a brake disk and other components of the brake mechanism (see. Head Brake system).
6. Screw a stupichny nut and tighten it strongly, but it is not final yet.
7. Establish a wheel. Lower the car on the earth and tighten wheel nuts with demanded effort (see. Head of Control and routine maintenance).
8. Finally tighten with demanded effort a stupichny nut, do not forget to fix its new shplinty (see. Head Coupling and power shafts).