Nissan Maxima QX

since 1993 of release

Repair and car operation


Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment

9a1e70e9

Removal and installation of a control lever of a forward suspension bracket

REMOVAL

 PERFORMANCE ORDER

1. Weaken nuts of fastening of the corresponding forward wheel. To Poddomkratta a car front also establish it on props. Remove a wheel.
2. Disconnect a rack of the stabilizer of cross-section stability from a control lever (see. Section Removal and installation of the forward stabilizer of cross-section stability). On models 1993 and 1994 of вып. remove a stabilizer bar (see in the same place).

3. On models 1993 and 1994 of вып. отболтите a spherical support from a suspension bracket control lever. On models since 1995 вып. take шплинт and weaken a nut of fastening of a spherical finger. By means of a special bifurcate stripper liberate a sharovy finger from assembly of a rotary fist.

 In the course of liberation of a spherical finger the protective cover of a support almost will be for certain damaged. Separate the lever from assembly of a rotary fist.

4. If the control lever of a suspension bracket needs replacement, weaken a nut of a finger of the plug of lever assembly. Turn out bolts of a finger of the plug.

5. Turn out bolts of fastening of the holder of the plug, then remove a control lever. On models 1993 and 1994 of вып. in case of need remove a lever kerchief.

CHECK

 PERFORMANCE ORDER

1. Estimate a condition of forward and back rubber plugs of a control lever, - the worn-out and cracked components are subject to replacement. Installation of new plugs should be made in the conditions of a car-care center workshop, otherwise it is necessary to replace the lever assembled.
2. Check the lever case on existence of signs of deformations. The damaged lever is not subject to restoration and should be replaced.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Track, that all fixture was tightened with demanded effort.

 Tightening of bolts of a finger of the plug and the holder of the forward plug (and also lever kerchiefs on models 1993 and 1994 of вып.) it should be made strictly in a certain order. Before a final tightening of bolts of the holder or a nut of a finger prop up the external end of the lever a jack for the purpose of introduction it on normal working height. Do not forget to replace шплинт fixing of a nut of a spherical finger.