Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   General information
   Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket
   Shock-absorber replacement / screw spring of rack-mount assembly
   Removal and installation of assembly of a rotary fist with a nave
   Removal and installation of assembly of a forward nave with the wheel bearing
   Removal and installation of the forward stabilizer of cross-section stability
   Removal and installation of a control lever of a forward suspension bracket
   Replacement of spherical support
   Removal, check of a condition and installation of racks of a back suspension bracket
   Removal and installation of assembly of a back nave with the wheel bearing
   Removal and installation of a bar of the back stabilizer of cross-section stability (model 1993 and 1994 of вып.)
   Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)
   Removal and installation of components of a back suspension bracket of models from 1995 вып.
   Removal and installation of a steering wheel
   Removal and installation of tips of steering drafts
   Replacement of protective covers of assembly of the steering mechanism
   Removal, dismantle and installation of reechny transfer
   Removal and installation of the steering pump
   Air removal from a hydraulic path of system of strengthening of a wheel
   Replacement of wheel hairpins
   Wheels and tires - the general information
   Corners of installation of wheels
+ Body
+ Onboard electric equipment





9a1e70e9



Removal, check of a condition and installation of racks of a back suspension bracket

Models 1993 and 1994 of вып.

REMOVAL

 PERFORMANCE ORDER

1. Prop up forward wheels protivootkatny boots. Weaken wheel nuts, поддомкратьте a back of the car and establish it on props. Remove back wheels.
2. To Otboltita from a rack a basic arm of a brake hose. On the models equipped with ABS, turn out a coupling bolt of a collar and separate from a rack a plait of electroconducting of the wheel sensor.
3. Without disconnecting a hydraulic hose, remove a support of the brake mechanism and a brake disk (see. Head Brake system). Tie up a support a wire to a bottom or suspension bracket element, - try not to allow tension of a brake hose.
4. If the rack needs replacement, remove nave assembly with the wheel bearing.
5. Disconnect from a rack longitudinal and cross-section levers (see. Section Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)).
6. Open a cover of a luggage compartment and remove the corresponding panels of internal furnish for the purpose of ensuring access to fixture of the top support of rack-mount assembly.
7. Remove a rubber cover of a support of the shock-absorber. Ask the assistant to hold rack-mount assembly and give the top fixing nuts. take assembly from under the car through a wheel arch. If the rack needs replacement, disconnect from it an arm of the longitudinal lever and transfer on replaceable assembly. track, that the fixture was tightened with demanded effort.

CHECK

 PERFORMANCE ORDER

Act according to the instructions provided in paragraphs 6 and 7 of the Section Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket. The description of procedure of dismantling are resistant (if in it there will be a need) see in the Section shock-absorber Replacement / a screw spring of rack-mount assembly.

INSTALLATION

 PERFORMANCE ORDER

1. Having used the help of the assistant, get a rack on the regular place under an arch of a wheel and accurately pass hairpins of its top support in reciprocal body openings. Screw, but do not tighten while, fixing nuts.
2. Connect to a rack longitudinal and cross-section levers (see. Section Removal and installation of levers of a back suspension bracket (model 1993 and 1994 of вып.)). Prop up a back suspension bracket a jack, having got the last under an arm of the longitudinal lever, - components should appear are hung out at normal working height. Tighten fixture cross-section and longitudinal levers with demanded effort.
3. Fix on a rack a basic arm of a brake hose. On models with ABS establish an arm of fastening of electroconducting of the wheel sensor.
4. Establish wheels, lower the car on the earth and tighten wheel nuts with demanded effort (see. Head of Control and routine maintenance).
5. Tighten with demanded effort of a nut of the top support of a rack. Establish to the place of the panel of an internal upholstery of a luggage compartment.

Models since 1995 вып.

REMOVAL

 PERFORMANCE ORDER

1. Prop up forward wheels protivootkatny boots. Weaken wheel nuts, поддомкратьте a back of the car and establish it on props. Remove back wheels.

2. Give a nut of a bolt of fastening of the bottom end of the shock-absorber to assembly of the back bridge.

3. Nuts of fastening of the top support of rack-mount assembly are located in a luggage compartment, - remove the corresponding panels of an internal upholstery. Ask the assistant to hold assembly and give the top fixing nuts. Take a rack from under the car through a wheel arch.

CHECK

 PERFORMANCE ORDER

1. Act according to the instructions provided in paragraphs 6 and 7 of the Section Removal, check of a condition and installation of rack-mount assemblies of a forward suspension bracket.
2. The description of procedure of dismantling are resistant (if in it there will be a need) see in the Section shock-absorber Replacement / a screw spring of rack-mount assembly.

INSTALLATION

 PERFORMANCE ORDER

1. Having used the help of the assistant, get a rack on the regular place under an arch of a wheel and accurately pass hairpins of its top support in reciprocal body openings. Screw, but do not tighten while, fixing nuts.
2. Connect the bottom end of the shock-absorber to assembly of the back bridge, pass in openings a fixing bolt. Prop up a suspension bracket a jack, deduce components on normal working height and tighten a nut of a fixing bolt with demanded effort.

 The jack should be got under an arm of the longitudinal lever of a suspension bracket, - at all under levers!

3. Tighten with demanded effort of a nut of the top support of a rack. Establish to the place of the panel of an internal upholstery of a luggage compartment.