Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and door handles
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment
9a1e70e9



Removal and installation of forward and back bumpers

 PERFORMANCE ORDER

1. Cock the parking brake, поддомкратьте the car and establish it on props.
2. Disconnect from the battery a negative wire.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! Disconnect all other electroconducting disturbing to dismantle of the corresponding bumper.

Front bumper

 PERFORMANCE ORDER

1. Remove established under a radiator and a bumper a radiator the antispray screen.
2. Remove a decorative front grille (see. Section Removal and installation of a decorative front grille). Remove assemblies of head headlights and indexes of turns (see. Head Onboard electric equipment).
3. Release clamps of fastening of an overlay of a bumper to panels of wings (see. The section Removal and installation of forward wings), then the remained clamps, - try not to damage a paint and varnish covering of wings or the polished surface of a slip.

4. Working under the car, turn out bolts of fastening of a beam of a bumper.

 Basic arms of a beam can be separated from the chassis by a way of an otdavaniye of nuts from their back party, or removal of insulating slips for the purpose of ensuring access to forward fixing bolts (after a bamperny slip).

5. Remove bumper Assembly from the car.
6. Installation is made upside-down.

Rear bumper

 PERFORMANCE ORDER

1. Under the car release plastic clamps of fastening of bottom edge of an overlay of a rear bumper. Do not forget to release also three clamps established over a platform under fastening of registration plate.

2. Open a cover of a luggage compartment and for the purpose of ensuring access to the top bolts of fastening of an overlay of a rear bumper remove the panel of a carpet upholstery of a floor.

3. In case of need turn out fixing bolts and remove a beam of a rear bumper.

4. Installation is made upside-down.