Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and door handles
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment
9a1e70e9



Removal, installation and adjustment of doors

 Doors of the car I have considerable weight therefore it will be reasonable to secure with the help of the assistant.

REMOVAL AND INSTALLATION

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery and the film insulating screen (see. Section Removal and installation of panels of an internal upholstery of doors). Disunite contact sockets and push electroconducting through technological openings in a doorframe, having provided with that possibility of free dismantle of the last.
2. Open a door against the stop and prop up it a jack, or wooden blocks. Remark: In order to avoid damage of LKP lay between a head of a jack and door edge a rags layer.

3. Turn out a bolt of fastening of the limiter of opening of a door.

4. Lead round loopy levels a marker, having marked situation them on a door.

5. Turn out fixing bolts and by means of the assistant accurately remove door assembly from the car. Installation is made upside-down.

ADJUSTMENT

 PERFORMANCE ORDER

1. Correctness of provision of a door in a body aperture has critical value from the point of view of serviceability of functioning of door assembly. First of all it is necessary to estimate size люфта axial fingers of door loops. Completely open a door and pull it up-down. If люфт doors are exceeded by 1.6 mm, it is necessary to replace loops.
2. For performance of correction of provision of a door in the vertical direction weaken bolts of fastening of loops on a car body (access to some bolts is limited therefore the key of a special form can be necessary). It is possible to consider a door established truly when in a closed position its upper edge appears it is parallel to a cut of a roof of the car, and bottom - threshold lines
3. Door alignment in the longitudinal direction is carried out by an otpuskaniye of bolts of fastening of loopy levels on a doorframe, - the special key again can be necessary. The first line (back at a back door) doors thus should appear aflush with a wing surface.
4. Serviceable operation of the locking mechanism can achieve by correction of position of the drummer of the lock in the vertical direction. For an assessment of size of shift lead round a plate of the basis of the drummer a marker. Weaken fixture and make necessary adjustment, - the latch should enter into gearing with the central part of the drummer.

5. In summary adjust position of the drummer in the horizontal direction, - the closed door should appear aflush with a surface of the rack/panel of a back wing and regularly thus to be locked.