Nissan Maxima QX + Nissan Maxima brand Cars + Maintenance instruction + Settings and routine maintenance + Engine + Systems of cooling, heating + Power supply system and release + engine Electric equipment + Control systems of the engine + Transmission + Coupling and power shafts + Brake system + Suspension bracket and steering - Body General information and precautionary measures Care of components of a body and car bottom Care of vinyl elements of furnish Care of an upholstery and salon carpets Repair of insignificant damages of body panels Repair of seriously damaged body panels Service of loops and car locks Replacement wind and other fixed glasses Removal and installation of a decorative front grille Removal, installation and adjustment of provision of a cowl Removal and installation of a latch of the lock of a cowl and cable of its drive Removal and installation of forward and back bumpers Removal and installation of forward wings Removal and installation of the panel of a forward reflector Removal and installation of panels of an internal upholstery of doors Removal, installation and adjustment of doors Removal and installation of a latch, cylinder of the lock and door handles Removal and installation of door glasses Removal and installation of regulators of window regulators Removal and installation of rear-view mirrors Removal, installation and adjustment of a cover of a luggage compartment Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment Removal and installation of driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank Removal and installation of the central console Removal and installation of finishing sections of the dashboard Removal and installation of sections of a casing of a steering column Removal and installation of the main section of the dashboard Removal and installation of seats Removal and installation of the back shelf Adjustment of the top hatch Body sizes + Onboard electric equipment
|
Removal and installation of finishing sections of the dashboard
Dashboard design
|
1 — the Deflector обдува a windscreen 2 — Stykovochny knot 3 — the Remote insert 4 — the Clamp of fastening of the deflector 5 — the Clamp 6 — the Sealing ring 7 — the Combination of devices 8 — the Clamp 9 — the Clamp 10 — the Decorative cover of the fixing screw
|
11 — the Clamp 12 — the Decorative cover of the fixing screw 13 — the Assembly bracket 14 — the Control panel functioning of a heater and To/in 15 — the Ware box 16 — Facing of the lever of switching 17 — the Facing slip 18 — the Decorative cover of the fixing screw 19 — the Slip 20 — the Decorative cover of the fixing screw |
|
Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation. |
The design of the dashboard is presented on an illustration.
Disconnect a negative wire from the battery.
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action! |
Facing of an instrument guard
|
1. Remove covers of a casing of a steering column (see. Section Removal and installation of sections of a casing of a steering column).
|
2. Turn out two fixing screws in the top part of facing of an instrument guard. Accurately hooking the screw-driver wound by an adhesive tape, release clamps and separate the lower part of facing of a guard from the dashboard.
|
On the models equipped with a control system of speed or anticreeping system, in facing the corresponding switches from which at the last stage of removal of the panel it is necessary to disconnect electroconducting are built in. |
|
3. Installation is made upside-down. Track reliability of a zashchelkivaniye of clamps. |
|
Knee emphasis
|
|
1. Uncover the salonny assembly block of safety locks, then turn out two screws, located on bottom edge of the panel of a knee emphasis. Remove persistent assembly. |
|
2. If the emphasis acts in film for the purpose of ensuring access to other components, it is enough to turn out fixture and to lower the panel. |
3. Installation is made upside-down. |
|
Central section of furnish
|
|
1. Having hooked the screw-driver wound by an adhesive tape, remove the central section of furnish from the car dashboard. |
2. Having separated the panel, disconnect electroconducting from the switches built in in it (see. Head Onboard electric equipment). 3. Installation is made upside-down. |
|
Ware box
|
1. Open a ware box and turn out four top and two bottom screws of fastening of assembly. Take a casing of a ware box from the dashboard.
2. Installation is made upside-down. |
|
|
|