The device, service, Nissan Maxima QX repair - Removal and installation of the main section of the dashboard//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and door handles
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment
9a1e70e9



Removal and installation of the main section of the dashboard

 PERFORMANCE ORDER

 Models of cars considered in the real Management are equipped with system of additional safety (SRS). Before starting performance of any works near the block of a safety cushion, a steering column or the dashboard, disconnect SRS in order to avoid receiving traumas at its casual operation (see. Head Onboard electric equipment). Electroconducting of a chain of SRS is easy for distinguishing on yellow color of isolation.

 Procedure of dismantle of the dashboard is represented rather difficult and its performance will charge more correctly to specialists of car-care center.

1. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Remove the central console (see. Section Removal and installation of the central console).
3. Remove sections of a casing of a steering column (see. Section Removal and installation of sections of a casing of a steering column).
4. Remove facing of an instrument guard (see. Section Removal and installation of finishing sections of the dashboard).
5. Remove an instrument guard (see. Head Onboard electric equipment).
6. Remove finishing sections of the dashboard (see. Section Removal and installation of finishing sections of the dashboard)
7. Remove a radio receiver and the control panel functioning of the heater/conditioner of air (see. Heads of System of cooling, heating and Onboard electric equipment).

8. Remove forward overlays of thresholds of both forward doors. Slips fasten by means of clamps and for office they are rather simple for hooking the suitable tool.

9. Remove panels of furnish of racks of a windscreen.

10. Assembly of a passenger safety cushion fastens to a back part of the dashboard. Disconnect the corresponding electroconducting, turn out bolts of fastening of the lower part of the module of a safety cushion to an intensifying beam of the dashboard.

 Bolts have TORX type heads, are sealed up and are given/are tightened by means of a special key.

11. Having hooked, remove deflectors обдува a windscreen and turn out the top bolts of fastening of the dashboard located under them.

12. Release other fixture and disconnect all brought to the elements of management built in in the panel electroconducting. Delay the panel back and take it from the car.

13. In the central part of a basic arm of the panel of devices / console assembly remove the body module of management (VSM), - previously mark all electroconducting brought to the module. Remove also ESM (see. Head of the Control system of the engine).

14. Having given the top and bottom fixture, remove two vertical basic arms, located in the central part of an intensifying beam. Turn out fixing bolts and remove from an intensifying beam the internal assembly block of safety locks and the lever of an otpuskaniye of the lock of a cowl.

15. Lower a steering column, having taken away it from an intensifying beam of the dashboard (see. Section Removal and installation of the heat exchanger of a heater).
16. Mark and disconnect brought to an intensifying beam of the dashboard electroconducting. Turn out fixing bolts, incline a beam and take it from the car (the right end forward).

17. Installation is made upside-down.