The device, service, Nissan Maxima QX repair - Care of an upholstery and salon carpets//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   General information and precautionary measures
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and other fixed glasses
   Removal and installation of a decorative front grille
   Removal, installation and adjustment of provision of a cowl
   Removal and installation of a latch of the lock of a cowl and cable of its drive
   Removal and installation of forward and back bumpers
   Removal and installation of forward wings
   Removal and installation of the panel of a forward reflector
   Removal and installation of panels of an internal upholstery of doors
   Removal, installation and adjustment of doors
   Removal and installation of a latch, cylinder of the lock and door handles
   Removal and installation of door glasses
   Removal and installation of regulators of window regulators
   Removal and installation of rear-view mirrors
   Removal, installation and adjustment of a cover of a luggage compartment
   Removal and installation of a latch and cylinder of the lock of a cover of a luggage compartment
   Removal and installation of driving cables of an otpuskaniye of locks of a cover of a luggage compartment and door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of the central console
   Removal and installation of finishing sections of the dashboard
   Removal and installation of sections of a casing of a steering column
   Removal and installation of the main section of the dashboard
   Removal and installation of seats
   Removal and installation of the back shelf
   Adjustment of the top hatch
   Body sizes
+ Onboard electric equipment
9a1e70e9



Care of an upholstery and salon carpets

Each three months remove rugs and mats and make cleaning of internal panels of an upholstery of salon. In case of need this procedure can be made more often. For garbage cleaning, and also for cleaning of rugs and mats it is possible to use a rigid brush or a sweeper. Further all surfaces follows carefully пропы лесосить, especially along seams, joints and material folds.

The eaten dirt can be removed from carpets by means of household or special automobile shampoos which for convenience are issued in the form of aerosols - follow instructions of manufacturers. In summary vacuum the processed site and "tousle" pile a rigid brush.

 Do not leave in salon for drying of the cleaned upholstery any electric heating devices!


The leather upholstery demands special leaving. Removal of spots should be made by means of very weak soap solution of warm water. Solution is put with soft rags, then the surface is wiped dry. At all do not use for rubbing of a leather upholstery alcohols, gasoline and other different solvents.

Try not to allow long hit on a leather upholstery of direct sunshine. Try to park the car in a shadow, use sun-protection curtains, etc.

1. In the absence of access to the back party of the panel of a body for dent percussion, it should be extended by means of a hammer with sliding the brisk. In the deepest place of a dent, or along its border, насверлите or fill small openings at distance not less than 2.5 cm from each other …

2. … then screw in a hammer rod in an opening and put it in action. Tap with a usual hammer at dent edge to help metal to accept an initial form. After the completion of this procedure the surface of a dent should come nearer to the initial contour and approximately on 0.3 cm act over a surface of surrounding metal.

3. By means of a rough emery paper remove paint to naked metal. It is possible to make it manually, but the adaptation shown on a photo, will help you to accelerate process. By means of thinner, approximately No. 320, an emery paper nullify paint in radius not less than 2.5 cm round a dent site.

4. After removal of paint it is better to check to the touch, than by sight, whether enough the metal surface is equal. Begin to knock a hammer of camber and/or extend hollows where it is necessary. Clear a restored surface wax or silicone spot remover.

5. Following instructions on packing, mix a pack of a plastic shpaklevka with a hardener. The proportion of mixing is critical and if you break it, the shpaklevka will stiffen too slowly or too quickly (and you will not manage to put it and to give the necessary form).

6. Working quickly let's stiffen to a shpaklevka, by means of a plastic applikator with pressing put it on a metal surface, making sure that there is a complete gearing to metal. Process a shpaklevka that it took the form, close to an initial form of a site and slightly towered over a surrounding surface.

7. Let's to a shpaklevka stiffen to such condition that it could be pressed through only a nail. By means of a file or the adaptation shown on a photo, roughly process a shpaklevka.

8. By means of the rough emery paper fixed on a plate or whetstone, process a shpaklevka that it became smooth and equal. Gradually pass to more and thinner grades of paper, always using a plate or whetstone, and finish processing number 360 or 400.

9. As a result of processing the hand should not feel transition border from a shpaklevka to naked metal and from naked metal to old paint. If this purpose is reached, remove a dust and cover the next panels and furnish details.

10. Put some layers of a first coat on a processed surface. Do not spray too much first coat that it did not flow down, and after drawing of each layer let's previous dry. Usually here the professional gun-razbryzgivatel is used, but in shops of auto parts there is on sale a first coat in inexpensive aerosol packing.

11. The first coat will help to reveal defects or scratches. Fill them with polishing paste. Following instructions on packing, process its thin (No. 360 or 400) an emery paper to smoothness. Repeat polishing, putting polishing paste and grinding it until the grounded surface does not become absolutely smooth.

12. Finish polishing by very thin paper (No. 400 or 600) to remove surpluses of a first coat. Wash up a site of processing by water and let's to it dry. Use a sticky napkin for complete removal of a dust, then put a layer of external paint. Do not try to wipe or put a wax covering on this site until paint will not dry completely (not less than two weeks).