Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
- Engine
   - SOHC engines
      General information
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of covers of heads of cylinders
      Removal, check of a condition and installation of assembly of yokes
      Replacement of maslootrazhatelny caps and klapanny springs with plates
      Removal and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Removal and installation of camshafts and pushers of valves
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal and installation of heads of cylinders
      Removal and installation of a pulley of a cranked shaft
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and flywheel installation / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
   + DOHC Engines
   + General major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





9a1e70e9



Removal and installation of the pallet of a case of the engine

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props.
3. At the corresponding complete set of the car remove protection of a case.
4. Merge impellent oil and remove the oil filter (see. Head of Control and routine maintenance).
5. Disconnect a Y-shaped reception pipe of system of production of the fulfilled gases from section following it (see. Head of the Power supply system and release).

6. Separate from the unit a cover of a dome of transmission.

7. Hang out the engine from above by means of the winch or a beam.

Take care of reliability of fixing of the unit the winch.

8. To Otboltita forward and back support of the power unit from a cross-section beam (see. Section Check of a condition and replacement of support of a suspension bracket of the power unit).
9. Remove passing under the case pallet a beam.

10. Operating as it should be, the return shown on an illustration, turn out bolts of fastening of the pallet.

11. Separate the pallet from the engine block. In case of need обстучите his priest to perimeter a hammer with soft brisk, - do not try to hook at all the "become attached" pallet the lever under an interfaced surface.
12. Clear interfaced surfaces of traces of a material of old laying and hermetic, then wipe their rags moistened in acetone.

INSTALLATION

 PERFORMANCE ORDER

1. Make sure of absoluteness of purity of carving openings in the engine block, - in case of need banish them a tap of the suitable size.
2. Grease with RTV hermetic end faces of epiploons and enclose the last in assembly of the oil pump and a back casing.
3. Impose a continuous pillow of RTV hermetic in diameter on an internal sealing surface of the pallet.

Installation of the pallet should be carried out within the next five minutes after hermetic imposing!

4. Press the pallet to an interfaced surface of the block of the engine, screw fixing bolts and, moving in strictly certain order, in four stages evenly tighten them with demanded effort.

5. Further installation is made as it should be the return to an order of dismantle of components.
6. Let's to hermetic dry up within about 30 minutes, then establish the new oil filter and fill in in the unit fresh engine oil. Start the engine and check pressure of impellent oil. Make sure of absence of leaks.