Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
- Engine
   - SOHC engines
      General information
      Preparatory actions and the list of repair procedures which can be executed without engine extraction from the car
      Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)
      Removal and installation of covers of heads of cylinders
      Removal, check of a condition and installation of assembly of yokes
      Replacement of maslootrazhatelny caps and klapanny springs with plates
      Removal and installation of a gas-distributing belt and cogwheels of a drive of GRM
      Removal and installation of camshafts and pushers of valves
      Removal and installation of the inlet pipeline
      Removal and installation of final collectors
      Removal and installation of heads of cylinders
      Removal and installation of a pulley of a cranked shaft
      Replacement of a forward epiploon of a cranked shaft
      Removal and installation of the pallet of a case of the engine
      Removal, check of a condition and installation of the oil pump
      Removal and flywheel installation / driving disk
      Replacement of a back epiploon of a cranked shaft
      Check of a condition and replacement of support of a suspension bracket of the power unit
   + DOHC Engines
   + General major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Replacement of maslootrazhatelny caps and klapanny springs with plates

 PERFORMANCE ORDER

Replacement of the broken klapanny springs and worn-out maslootrazhatelny caps can be made without dismantle of heads of cylinders. Two special adaptations and a source of the compressed air will be necessary only. Before starting works, make sure available near at hand rather powerful tool for a szhimaniye of the hard klapanny springs used for a complete set of engines of considered models of cars.

1. Uncover (also) heads (ok) cylinders (see. Section Removal and installation of covers of heads of cylinders).
2. Take assemblies of yokes (see. The section Removal, check of a condition and installation of assembly of yokes), then remove assembly directing pushers of the corresponding valves (see. Section Removal and installation of camshafts and pushers of valves).
3. Turn out a spark plug from the cylinder which components need replacement. If there is a need for replacement of maslootrazhatelny caps, turn out all candles.
4. Having turned a cranked shaft, bring the corresponding piston into the provision VMT of the end of a step of compression (see. The section Reduction of the piston of the first cylinder in the provision of the top dead point (VMT)). At replacement of maslootrazhatelny caps, begin with the first cylinder, then pass from one to another as ignition (see. Specifications).

5. Screw in a candle opening of the corresponding cylinder a long transitional nozzle and connect to it a hose from a source of the compressed air.

Special carving nozzles with the union of fast connection are issued - ask in car-care center shops.

6. Submit air to the cylinder.

Under the pressure of air поршеньможет to move down that will lead to a sudden provorachivaniye of a cranked shaft - do not leave on a bolt screwed in a pin of a shaft, a face key by means of which brought the piston into situation VMT. Valves will be kept on a place by pressure of air.

7. In order to avoid hit in the engine of garbage and other extraneous subjects, закупорьте rags all openings in the block round valves subject to service. Now by means of the special tool compress a spring of the served valve. By means of tweezers or the magnetized core take from flutes on a valve core crackers of the cutting lock.

If to fix the valve in a closed position the compressed air it is not possible, therefore, the violation of tightness defined by existence of mechanical defects of a working facet of a plate of the valve or its saddle takes place. In that case the head of cylinders is necessary for removing from the engine for the purpose of performance of the corresponding regenerative repair.

8. Remove from a valve core a plate of a spring, the filter, and actually a spring, then remove from the directing plug a maslootrazhatelny cap.
9. Fix on the top end of a core of the valve a rubber bandage, or reel up an adhesive tape to exclude possibility of falling of the valve in the combustion chamber, then block supply of air in the cylinder.
10. Check a valve core on existence of signs of wear or mechanical damages. Rotating the valve in the directing plug, estimate size radial люфта its end face, defining degree of straightness of a core (the bent valve is subject to replacement).
11. Move the valve up-down in the directing plug, trying to reveal the jamming points which existence testifies or to deformation of a core of the valve, or about plug damage - in any case the head is subject to removal for the purpose of performance of necessary regenerative repair.
12. Again submit air to the cylinder for the purpose of valve fixing. Remove from a core a rubber bandage/adhesive tape.

13. Grease a valve core with pure impellent oil and establish a new maslootrazhatelny cap. For installation of maslootrazhatelny caps of inlet valves it is necessary to use a special opravka, or a face head of the suitable size (the cap is put on the plug against the stop). Caps of final valves are established only manually and on strictly certain depth.

Caps of inlet and final valves differ from each other according to the instruction - do not mix components.

14. Put on a valve core internal and external klapanny springs (an end face with the truncated step of rounds to a head).

15. Plant on a spring a plate, then compress a spring (ы) by means of the special tool and accurately fill in a landing flute on a valve core crackers of the cutting lock. For temporary fixing of crackers to an otpuskaniye of the tool grease them from within with dense greasing.

16. Watching correctness of landing of crackers in a flute, release the adaptation for a spring szhimaniye.
17. Block supply of air in the cylinder and turn out from a candle opening a transitional nozzle.
18. Establish into place a valve pusher (see. The section Removal and installation of camshafts and pushers of valves), then establish assemblies of yokes (see. Section Removal, check of a condition and installation of assembly of yokes).
19. Establish a cover of a head of cylinders (see. Section Removal and installation of covers of heads of cylinders).
20. Screw to the place of a spark plug and connect to them (in a demanded order) wire VV.
21. Start the engine and check it on existence of signs of leakages of oil and the unusual noise published by the klapanny mechanism.