The device, service, Nissan Maxima QX repair - Removal and receiver dehumidifier installation To/in//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
- Systems of cooling, heating
   General information
   Antifreeze - general information
   Check of serviceability of functioning and thermostat replacement
   Check of a condition of fans of system of cooling and chains of their inclusion, replacement of components
   Removal and installation of a radiator and expanded tank of system of cooling
   Check of a condition and replacement of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of a measuring instrument of temperature of cooling liquid
   Check of serviceability of functioning of the driving electromotor of the fan of a heater and condition of components of its electric chain, …
   Removal and installation of the electromotor of a drive of the fan of a heater
   Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Removal and receiver dehumidifier installation To/in
   Removal, service and To/in compressor installation
   Removal and To/in condenser installation
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Removal and receiver dehumidifier installation To/in

Air central air constantly is under a high pressure. At all do not disconnect refrigerator lines and do not remove any components of system, previously without having executed a discharge of the last. The discharge of central air of air should be made by strengths of the skilled expert in the conditions of a car-care center workshop. At a rassoyedineniye of refrigerator lines surely put on goggles!

At replacement of components of central air of air the certain amount of replaceable refrigerator oil necessary for filling of volume of new knot is required. Use only the oil good for the use in R-134a systems (attentively study a label on the container).

REMOVAL

 PERFORMANCE ORDER

1. The receiver dehumidifier carries out a role of the accumulator of a coolant, and also serves for removal from moisture system. At replacement of large components of central air of air (the compressor, the condenser, the evaporator), and also at hit in a refrigerator path of air assembly of an accumulator/dehumidifier is subject to replacement.
2. Make central air discharge in the conditions of a specialized workshop. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. Disconnect electroconducting from the cyclic sensor switch of the coupling of coupling of the compressor in the top part of assembly of a receiver dehumidifier.

At replacement of a receiver dehumidifier transfer the old sensor switch on the new block.

4. Disconnect from a receiver refrigerator lines, at once закупорьте the open ends of tubes and unions in order to avoid hit in dirt system.

5. Weaken a coupling bolt and liberate receiver dehumidifier assembly from a fixing collar (a basic arm).

INSTALLATION

 PERFORMANCE ORDER

1. At replacement of assembly of a receiver dehumidifier about 2 ounces (60 ml) refrigerator oil which it is necessary to fill in the replaceable block is required.
2. Establish assembly on the regular place and slightly tighten a coupling bolt of a fixing collar, having left assembly some degree of freedom necessary at connection of hydraulic lines.
3. Connect to assembly inlet and final refrigerator lines (before joining of shtutserny knots grease new sealing rings with pure refrigerator oil). Having finished connection of lines, strongly tighten a coupling bolt of a fixing collar.
4. Connect a negative wire to the battery.
5. Make a charging of system and its check on leaks in the conditions of a specialized workshop.