The device, service, Nissan Maxima QX repair - Check of a condition and replacement of fuel lines and their shtutserny connections//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
- Power supply system and release
   General information
   Sbrasyvaniye of pressure in a power supply system
   Check of serviceability of functioning of the fuel pump, measurement of pressure of fuel
   Check of a condition and replacement of fuel lines and their shtutserny connections
   Removal and installation of the fuel pump
   Check of a condition and replacement of the sensor of fuel consumption
   Removal and installation of a fuel tank
   Cleaning and repair of a fuel tank - general information
   Removal and installation of assembly of an air purifier
   Removal, installation and adjustment of a cable of an accelerator
   System of electronic injection of fuel (EFI) - the general information
   Check of serviceability of functioning of system of injection
   Check of a condition and replacement of the case of a throttle
   Removal and installation of a regulator of pressure of fuel
   Removal and installation of the fuel highway and injection injectors
   Check and adjustment of turns of idling
   Release system - the general information
+ engine Electric equipment
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Check of a condition and replacement of fuel lines and their shtutserny connections

See preventions at the beginning of pressure Sbrasyvaniye's Section in a power supply system.


 PERFORMANCE ORDER

1. Before starting service of fuel lines or their shtutserny connections it is necessary to dump pressure in a power supply system (see. Undressed Sbrasyvaniye pressure in a power supply system).
2. Lines of a fuel path of a power supply system are laid between a fuel tank and an impellent compartment. Steel tubes and flexible fuel hoses fasten to the car bottom by means of clips and screw fixture. Each time when the car rises over the earth with any purpose (for example, for survey or replacement of components of system of production of the fulfilled gases), try to use a case and to check a condition of fuel lines and their shtutserny connections. Attentively examine all hoses and tubes of a fuel path on existence of cracks, twisting, deformations and other mechanical damages.
3. At identification of signs of internal pollution or passableness violation the corresponding section of a fuel path is necessary for removing and blowing the compressed air. Without fail check also a condition of the mesh filter of a toplivozabornik of the pump (see. Section Check of a condition and replacement of the sensor of fuel consumption).

Steel tubes

Use as replaceable sections only high-strength steel tubes of production of the proved manufacturers.

Remember that copper and aluminum tubes are not capable to sustain vibrating loadings arising in use the car.

Do not forget that fuel lines on the models equipped with system of injection, should maintain high internal pressure.

Often in firm shops of automobile accessories it is possible to get the sections of metal tubes equipped with carving shtutserny nozzles. During the easing and a tightening of shtutserny connections use two wrenches to avoid a provorachivaniye of a reciprocal part of the socket. Without fail check a condition of shtutserny connections of sealing rings used for sealing. The worn-out or mechanically damaged rings at once replace. Try to use as replaceable components only firm details.

Flexible hoses

At replacement of fuel hoses use only firm components calculated on high internal pressure.


Flexible fuel hoses should be laid not closer than in 10 cm from components of system of production of the fulfilled gases and is not closer than in 25 cm from the catalytic converter. Watch, that fuel lines did not adjoin to body elements and suspension bracket components. The minimum admissible size of a gap makes 6.3 mm.

REPLACEMENT

 PERFORMANCE ORDER

1. The damaged sections of fuel lines (tubes or hoses) should be removed and replaced new, firm production.
2. Dump pressure in a power supply system (see. Undressed Sbrasyvaniye pressure in a power supply system).
3. Liberate section of a fuel path subject to dismantle from intermediate clamps of fastening it to the car bottom.
4. At the corresponding complete set release a collar (ы) and disconnect a hose (and) from the metal line (й). In case of need for release повращайте a hose on the union for simplification of its detachment.
5. Installation is made upside-down.