Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information and precautionary measures
   Check of functioning of system of ignition
   Check of a condition and replacement of coils of ignition
   Check of a condition and replacement of the power transistor (model 1993 and 1994 of вып.)
   Check, adjustment, removal and installation of the distributor of ignition (model 1993 and 1994 of вып.)
   Check and adjustment of installations of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter and start chain
   Removal and starter installation
   Replacement of the traction relay
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Check and adjustment of installations of a corner of an advancing of ignition

 Possibility of adjustment of installations of a corner of an advancing of ignition is provided only on models 1993 and 1994 of вып. on models since 1995 вып. the corner of an advancing of ignition is not subject to adjustment, however check it allows to estimate serviceability of functioning of a control system of ignition.


 PERFORMANCE ORDER

1. At the switched-off ignition according to instructions of manufacturers connect a stroboscope. On models 1993 and 1994 of вып. the induction receiver of a stroboscope is connected to VV to a wire of a spark plug of the first cylinder. on models since 1995 вып. in a plait of electroconducting of the corresponding coil of ignition the special loop for connection of the induction sensor of a stroboscope is provided.

 If the design of a stroboscope does not allow to connect it to a loop of VV of electroconducting, remove the coil of the first spark plug. Restore initial connection of electroconducting, connect a candle wire between the coil and a spark plug and to it connect a stroboscope.

2. Cock the parking brake, prop up back wheels of the car protivootkatny boots and transfer transmission to the situation "R" or "N".
3. Find adjusting labels on a pulley of a cranked shaft (the index is fixed on a cover of a drive of GRM). VMT label on a pulley is illuminated by yellow paint. On models 1993 and 1994 of вып. the step of an arrangement of labels on a pulley makes 5 °, the label of VMT is extreme left. Find a label 15 ° before VMT. In case of need wipe a pulley for review improvement.

4. Start the engine and warm up it to normal working temperature (the top hose of a radiator should become hot to the touch). Make sure of correctness of installation of turns of idling of the engine (see. Head of the Control system of the engine). Lift turns to value 2000 in a minute, then again dump them to the single.
5. Direct a stroboscope beam on a pulley of a cranked shaft and check installation of a corner of an advancing of ignition (the corresponding label will motionlessly settle down opposite to the index).
6. On models 1993 and 1994 of вып. in case of need weaken clamping a bolt of fastening of the distributor and, rotating the case of the last, make the corresponding correction of a corner of an advancing of ignition. Strongly tighten a bolt and repeat check.
7. On models since 1995 вып. in case of violation of installation of a corner of an advancing of ignition check serviceability of functioning of sensors of provision of cranked and distributive shaft (see. Head of the Control system of the engine). If sensors as it should be, drive away the car on car repair shop for carrying out diagnostics and regenerative repair of RSM.
8. Muffle the engine and disconnect a stroboscope.