Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information and precautionary measures
   Check of functioning of system of ignition
   Check of a condition and replacement of coils of ignition
   Check of a condition and replacement of the power transistor (model 1993 and 1994 of вып.)
   Check, adjustment, removal and installation of the distributor of ignition (model 1993 and 1994 of вып.)
   Check and adjustment of installations of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter and start chain
   Removal and starter installation
   Replacement of the traction relay
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





9a1e70e9 canadian health care mall



Removal and generator installation

Generator design (models 1993 and 1994 of вып.)

1 — the Pulley
2 — the Forward cover
3 — the Rotor
4 — the Back bearing
5 — the Nut (39 ÷ 59 Nanometer)
6 — the Forward bearing

7 — the Holder of the bearing
8 — Stator
10 — Shchetochnaya assembly
11 — the Back cover
12 — Coupling bolts (3.1 ÷ 3.9 Nanometer)


Generator design (models since 1995 вып.)

1 — the Pulley
2 — the Forward cover
3 — the Forward bearing
4 — the Holder of the bearing
5 — the Rotor
6 — the Contact ring
7 — Stator
8 — Coupling bolts (3.1 ÷ 3.9 Nanometer)

9 — Details of installation of contact
10 — the Condenser
11 — Shchetkoderzhatel
12 — the Regulator
13 — Diode assembly
14 — Laying
15 — the Back cover

Models 1993 and 1994 of вып.

 PERFORMANCE ORDER

1. The design of the generator is presented on an illustration.
2. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. To Poddomkratta the car also establish it on props. At the corresponding complete set remove protection of a case.
4. Remove a driving belt (see. Head of Control and routine maintenance).
5. Disconnect from the generator electroconducting and a final wire.
6. Turn out fixing bolts and separate the generator from the engine block.

7. Installation is made upside-down.
8. Do not forget to establish in summary a driving belt and to connect a negative wire to the battery. Adjust effort of a tension of a belt (see. Head of Control and routine maintenance).

Models since 1995 вып.

 PERFORMANCE ORDER

1. The design of the generator is presented on an illustration.
2. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

To Poddomkratta the car also establish it on props. At the corresponding complete set remove protection of a case and a loker of protection of an arch of the right forward wheel.
3. Remove a driving belt (see. Head of Control and routine maintenance).

4. Disconnect from the generator electroconducting and a final wire.

5. Remove assembly of fans of system of cooling with a casing (see. Head of System of cooling, heating).
6. Remove the To/in compressor and, without disconnecting hydraulic lines, shift it aside.

7. Turn out fixing bolts and separate the generator from the engine block.

8. Installation is made upside-down.
9. Do not forget to establish in summary a driving belt and to connect a negative wire to the battery. Adjust effort of a tension of a belt (see. Head of Control and routine maintenance).