The device, service, Nissan Maxima QX repair - Removal and starter installation//Maxim's Nissan (from 1993 g) accessories-sale.ru

Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
- Engine electric equipment
   General information and precautionary measures
   Engine start from the auxiliary power supply
   Check of a condition and battery replacement
   Check of a condition and replacement of wires of the battery
   Ignition system - the general information and precautionary measures
   Check of functioning of system of ignition
   Check of a condition and replacement of coils of ignition
   Check of a condition and replacement of the power transistor (model 1993 and 1994 of вып.)
   Check, adjustment, removal and installation of the distributor of ignition (model 1993 and 1994 of вып.)
   Check and adjustment of installations of a corner of an advancing of ignition
   Charge system - the general information and precautionary measures
   Check of a condition of system of a charge
   Removal and generator installation
   Start system - the general information and precautionary measures
   Check of serviceability of functioning of a starter and start chain
   Removal and starter installation
   Replacement of the traction relay
+ Control systems of the engine
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Removal and starter installation

Design of a starter of S114-461 (model 1993 and 1994 of вып.)

1 — the Holder
2 — the Coupling
3 — the Bolt (6.4 ÷ 7.8 Nanometer)
4 — the Case
5 — the Spring
6 — the Adjusting washer
7 — the Nut (7.4 ÷ 9.8 Nanometer)
8 — the Cover
9 — the Returnable spring
10 — the Lock ring
11 — the Lever
12 — the Boot

13 — the Traction relay
14 — the Anchor
15 — an excitement Winding
16 — the Case
17 — the Brush (-)
18 — a brush Spring
19 — the Back cover
21 — the Bolt (4.9 ÷ 6.4 Nanometer)
22 — the Brush (+)
23 — the Shaft


Design of a starter of S114-801A (model since 1995 вып.)

1 — the gear wheel Case
2 — the Adjusting lever
3 — the Boot
4 — the Traction relay
5 — the Washer
6 — the Nut (7.4 ÷ 9.8 Nanometer)
7 — the Slip
8 — the Gear wheel of internal gearing
9 — Bolts (4.9 ÷ 6.4 Nanometer)
10 — Bolts (6.4 ÷ 7.8 Nanometer)
11 — a gear wheel Emphasis
12 — the Gear wheel
13 — the Lock ring

14 — the Central suspension bracket (R)
15 — a gear wheel Shaft
16 — Planetary transfer
17 — the Central suspension bracket (And)
18 — the Case
19 — the Anchor
20 — the Brush (+)
21 — the Brush (-)
22 — a brush Spring
23 — the Persistent washer
24 — the Back cover
25 — Shchetkoderzhatel


 PERFORMANCE ORDER

1. The design of a starter is presented on illustrations.
2. Disconnect a negative wire from the battery.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

3. Remove air purifier assembly with an inlet air line (see. Head of the Power supply system and release).
4. Disconnect electroconducting from starter assembly with the traction relay.

5. Give fixing bolts and separate starter assembly from the engine.