Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
- Control systems of the engine
   General information
   System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions
   Removal and RSM installation
   Check of serviceability of a condition, replacement and adjustment of the sensor of provision of a butterfly valve (TPS)
   Check of a condition and replacement of the sensor of measurement of weight of an air stream (MAF)
   Check of a condition and replacement of the sensor of absolute pressure in the pipeline (MAR)
   Check of a condition and replacement of the sensor of temperature of soaked-up air (IAT)
   Check of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats)
   Check of a condition and replacement of the sensor of provision of a cranked shaft (SKR)
   Check of a condition and replacement of the sensor of provision of a camshaft (SMR)
   Check of a condition and replacement of the sensor switch of pressure in system of hydrostrengthening of a wheel (PSP)
   Check of a condition and replacement of the oxygen sensor (l-probe)
   Check of a condition and replacement of the sensor of a detonation
   Check of a condition and replacement of the sensor of temperature of fuel of speed of movement of the car (VSS)
   Check of a condition and replacement of the sensor of speed of movement of the car (VSS)
   Check of a condition and replacement of components of system of stabilization of turns of idling
   Control system of functioning of the capacity valve
   System of operated ventilation of a case (PCV)
   System of a retsirkulyatsiya of the fulfilled gases (EGR) - the general information, check of a condition and replacement of components
   System of catching of fuel evaporations (EVAP) - the general information, check of a condition and replacement of components
   The catalytic converter - the general information, check of a condition and replacement
+ Transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
9a1e70e9



Check of a condition and replacement of the sensor of temperature of cooling liquid of the engine (eats)

The eats sensor also represents a termistor (see. The section Check of a condition and replacement of the sensor of temperature of soaked-up air (IAT)). On models 1993 and 1994 of вып. the sensor is placed in the inlet branch pipe of water passing behind the distributor of ignition, on models since 1995 вып. - in a final branch pipe behind the left (forward) head of cylinders. Change of resistance of the sensor makes direct impact on amplitude of the signal which is given out by it on RSM. Thus, with temperature REDUCTION resistance of the sensor INCREASES, and on the contrary. RSM uses information issued by the sensor at determination of working temperature of the engine. Refusal eats sensor/violation in its electric chain lead to record in the block of memory of system of self-diagnostics of the corresponding code (see. The section System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions).

CHECK

 PERFORMANCE ORDER

 Performance described below procedure can lead to entering in memory of OBD of malfunction which will be highlighted by a control lamp “Check the engine”. On termination of check and the corresponding regenerative repair do not forget to clear memory of system (see. The section System of onboard diagnostics (OBD) - a principle of functioning and codes of malfunctions).

1. Before starting directly an assessment of a condition of the sensor, make sure of serviceability of giving of a food on it from RSM and in lack of signs of violations of grounding. Disconnect from the eats sensor electroconducting and connect the voltmeter to two plugs of the socket from a plait. Include ignition (the engine do not start), - the measuring instrument should issue the indication 5.0 In, otherwise check an electroconducting condition on a chain site between the sensor and RSM. If a chain as it should be, drive away the car on car repair shop for carrying out diagnostics of a condition of RSM and performance of the corresponding regenerative repair.
2. At the switched-off ignition disconnect from the eats sensor electroconducting and by means of an ohmmeter measure resistance between two plugs of the socket of the sensor at the cold engine. Restore initial connection of electroconducting, start the engine and warm up it to normal working temperature. Again disunite the socket and repeat resistance measurement. Compare results of two measurements to the schedule of temperature dependence of the sensor. The faulty sensor is subject to replacement.

 Thinner check of a condition of the eats sensor can be made out of the car and creation of the full schedule of temperature dependence by lowering in water warmed up on fire.

REPLACEMENT

 PERFORMANCE ORDER

 Before starting procedure performance, wait complete cooling of the engine.

1. Before installation of the new sensor wind its carving part with the FUM teflon tape/tape.
2. Disconnect from the sensor electroconducting and turn out it from the corresponding branch pipe of a path of system of cooling. As soon as possible (for the purpose of minimization of losses of liquid) screw to the place of the removed sensor new and strongly it tighten.
3. Check level of cooling liquid, in case of need make the corresponding adjustment (see. Head of Control and routine maintenance). Start the engine, warm up it to normal working temperature and check on existence of signs of leaks. After engine cooling again check level of its cooling liquid.