Nissan Maxima QX

since 1993 of release

Repair and car operation



Nissan Maxima QX
+ Nissan Maxima brand Cars
+ Maintenance instruction
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Control systems of the engine
- Transmission
   - 5-step manual box of gear shifting (RKPP)
      General information
      Removal and installation of components of a drive of gear shifting
      Replacement of epiploons
      Check and replacement of the sensor switch of fires of a backing
      Removal and RKPP installation
      Major maintenance of RKPP
   + 4-step automatic transmission (AT)
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





9a1e70e9



Removal and installation of components of a drive of gear shifting

Components of a drive of gear shifting

1 — the Handle of the lever of switching
2 — the Clamp of a protective cover
3 — the Protective cover of the lever
4 — the Boot
5 — the Spring
6 — the gear shifting Lever
7 — the Top bearing
8 — Nizhny the bearing
9 — the Plug
10 — the Ring
11 — the Boot
12 — the Ring
13 — the Plug
14 — Rubber laying

15 — the Holder
16 — the Nut (12 ÷ 15 Nanometer)
17 — the Bolt (4.4 ÷ 5.9 Nanometer)
18 — the Nut (35 ÷ 47 Nanometer)
19 — the Plug
20 — the Washer
21 — the Bolt (27 ÷ 36 Nanometer)
22 — the Holder of a basic bar
23 — the Basic bar
24 — the Suspension bracket of a returnable spring
25 — a management Rod
26 — the Nut (14 ÷ 18 Nanometer)
27 — the Nut (16 ÷ 21 Nanometer)
28 — the Returnable spring

REMOVAL

 PERFORMANCE ORDER

 Some of considered models are equipped with system of additional safety (SRS). Before starting service of the components located on proximity from safety cushions, surely disconnect SRS system (see. Head Onboard electric equipment).

1. Disconnect a negative wire from the battery. On the models equipped with SRS also disconnect from the battery a positive wire, then wait not less than three minutes, after it can start procedure performance.

 If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. To Poddomkratta the car also establish it on props. Remove the catalytic converter and the thermofilter.

3. Disconnect from transmission a basic bar and a management rod.

4. Give a nut of boltovy connection of fastening of a rod of management of switching to the gear shifting lever. Disconnect a returnable spring and give nuts of fastening of a basic bar to a nest of the lever and a weight damper. Remove assembly of a drive of gear shifting. Check a condition of plugs since both ends of a basic bar and a management rod. In case of identification of cracks replace the failed components.

5. Remove the console (see. Head Body). Disconnect a protective cover of the lever from the floor panel, liberate the lever of gear shifting and remove from it a cover, a saddle, an insulator and a reception nest. Attentively check a condition of all components, in case of identification of cracks, cuts, deformations and other mechanical damages make the corresponding replacements. Special value has faultlessness of a condition of a reception nest of the lever and its saddle, - excessive wear of these components leads to difficulties at gear shifting. It will be also reasonable to replace the torn or cut big protective cover of the lever.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Do not forget to grease all persistent and rubbing surfaces, including a spherical support of the lever and an internal surface of its reception nest with silicone greasing. Grease also plugs of a rod of management and a basic bar. Track reliability of a tightening of fixture.